CTC Union 8309D Manual do Utilizador

USER MANUAL IMC-1000M(S) Industrial Gigabit Ethernet OAM/IP Web Smart Media Converter

1.6 Panel 1000M 1000MS LED Indicators (see next page) 1 x RJ-45 port, supports 10/100/1000M Ethernet The LAN Spe

1.7 LED Indicators IMC-1000M and IMC-1000MS have LEDs on the front face that report the condition of power, Fiber link & Speed, LAN link &

Chapter 2 Installation 2.1 Mounting Options IMC-1000M(S) comes with both wall mount and DIN rail hardware brackets. When installing the DIN rail br

2.2 Electrical Installation Power & Alarm 9.6 ~ 60VDC Dual Inputs A removable terminal block provides both power and alarm connect

2.3 Installation of SFP Modules CTC Union supplied SFP modules are of the Bale Clasp type. The bale clasp pluggable module has a bale clasp that secur

Chapter 3 Web Based Provisioning 3.1 Introduction In an effort to make Networking devices easier to configure, many devices can now be configured via

3.3 Web Main Page 16

3.4 System Information 3.4.1 Network Information The information displayed on this page gives specific device, network information, and port status fo

3.4.2 DD Information The DD or DDOM information is read from the MSA compliant SFP module and can be displayed via the web user interface.

3.5.1 IP Configuration Use this screen to set the TCP/IP configuration for the local unit. Note, that if you change the IP address you could lose remo

3.5.2 Password Setting This function is used to modify the default password for the device. The password is required so that only authorized users ha

3.5.3 Converter Configuration The Converter configuration menu includes special features of IMC-1000MS. All of these spec

The remote Management functions of the converter can be disabled. Once disabled and saved, regardless of the 802.3ah OAM settings, the remote managem

Management Packet High Priority is a function which is enabled by default. Unless VLAN is enabled, this function is meaningless. The packet priority

3.5.4 Port Configuration This screen is for the configuration of the electrical Ethernet port (TP) and the optical port (FX). Both the TP an

3.5.5 MIB Counters The counters have an accumulation of received bytes and packets for each port (UTP, Fiber and Manageme

3.5.6 SNMP Configuration SNMP or Simple Network Management Protocol is an industry standard, ISO layer 7 application, for management of network device

3.6.7 VLAN 3.6.7.1VLANGroup By default, this device is VLAN unaware, making it completely transparent to VLAN tags. In mo

3.6.7.2VLANPerPortConfiguration Within the IMC-1000MS there are actually three different ports, the external copper and fiber ports,

3.6.8 Management VLAN Setting This function is independent of any other VLAN group or per port settings. The settings here provide a very quick method

CTC Union Technologies Co., Ltd. Far Eastern Vienna Technology Center (Neihu Technology Park) 8F, No. 60 Zhouzi St., Neihu, Taipei 114, Taiwan T +8

3.6.9 Alarm Configuration IMC-1000MS has an alarm relay with NO (normally open) and NC (normally closed) relay contacts which are available at the ter

3.7 Remote Settings When 802.3ah is active in both the local and remote unit (with fiber connection), the in-band management provides an embedded chan

3.8.1 802.3ah Configuration To use the OAM functions, the 802.3ah Function setting must be enabled. It is not enabled by default. T

3.8.2 Loop back Test The loop back test is a non-intrusive test which uses OAM packets and will not affect normal transmissions. The number of

3.8.3 802.3ah Status The Global Config fields display the state of OAM, if OAM is enabled. We can also see the MAC addres

Most information carried by OAMPDU is encoded using type-length-value (TLV) format. The first octet (or byte) of the OAMPDU indicates th

One of the most critical problems in an access network for carriers is differentiating between a simple power failure at the customer premise an

3.9.1 System Reboot When the converter is rebooted, all counters and registers are cleared and the converter starts fresh. If OAM is enabled, the disc

3.9.3 Firmware Upgrade If bugs are discovered, if functions are added, or if factory default settings are changed, the firmware in the converter will

Next, click the “Upgrade” button. The “Upload success!” indicates the image was transferred OK. Do not do anything for the next 60 second

Legal The information in this publication has been carefully checked and is believed to be entirely accurate at the time of publication. CTC Union Tec

3.10 Logout Logging out will ensure that the management session with IMC-1000MS is terminated. This is especially important if you are using a public

3.11 Troubleshooting 3.11.1 Factory Default. Apply power to IMC-1000MS and allow 25-30 seconds to fully boot. Using a pencil or ball-point pen, press

3.11.3 LED Observations 3.11.3.1PowerOnAt initial power on, PWR LED will not be lit. If active LAN is connected to the TP port, that Link and Speed

With IMC-1000MS reset to factory default, connect a PC and configure the PC to the 10.1.1.0 network (10.1.1.100 recommended). Use a PC to ping IMC-100

Table of Contents CHAPTER1INTRODUCTION...

3.7REMOTESETTINGS ...

Chapter 1 Introduction 1.1 Welcome Thank you for choosing IMC-1000M(S) Industrial Gigabit Ethernet OAM/IP Web Smart Media Converter. Throughout this d

1.3 Product Features  Redundant dual DC inputs  IP30 rugged metal housing  Wide temperature model supported (-20C~75C)  Auto-Cross over for MD

1.4 Specifications  Optical Interface  Connector SFP cage (1000MS) or Duplex SC, ST, FC (1000M)  Data rate 100/1000Base-FX (125Mbps/1.25GM